View C981U222KWDBA7317_9077231.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 ? 864-963-6300 ? www.kemet.com c 1066_x1_760 vac_y1_500 vac ? 1/13/2017 1 overview kemets 900 series encapsulated radial leaded ceramic disc capacitors are specifcally designed for interference- suppression ac line fltering applications. having internationally recognized safety certifcations, these capacitors are well-suited for applications that require keeping potentially disruptive or damaging line transients and emi out of susceptible equipment. they are also an ideal solution when needing to suppress line disturbances at the source. safety certifed capacitors are classifed as either x and/ or y capacitors. class x capacitors are primarily used in line-to line (across-the-line) applications. in this application there is no danger of electric shock to humans should the capacitor fail, but could result in a risk of fre. the class y capacitor is primarily used in line-to-ground (line by-pass) applications. in this application, failure of the capacitor could lead to danger of electric shock. with a working voltage of 760 vac in line-to-line (class x)and 500 vac in line-to-ground (class y) applications, these safety capacitors meet the impulse test criteria outlined in iec standard 60384. meeting subclass x1 and y1 requirements, these devices are certifed to withstand impulses up to 4 kv (x1) and 8 kv (y1) respectively. these encapsulated devices also meet the fame test requirements outlined in ul standard 94vC0. radial leaded ceramic disc capacitors safety standard recognized, 900 series, encapsulated, as type, x1 760 vac/y1 500 vac (industrial grade) ordering information c9 6 1 u 222 m w w d a a 7317 ceramic series body diameter lead spacing 1 spec. capacitance code (pf) capacitance tolerance rated voltage dielectric/ temp. char. design lead srk 1 failure rate packaging (c-spec) c9 = ceramic 900 series 1 = 8.0 mm 2 = 9.0 mm 3 = 10.0 mm 5 = 12.0 mm 6 = 13.0 mm 7 = 14.0 mm 8 = 15.0 mm 1 = 10.0 mm u = safety two signifcant digits and number of zeroes k = 10% m = 20% w = x1 760 vac /y1 500 vac w = y5u d = disc a = straight b = vertical kink c = outside kink a = n/a see "packaging c-spec ordering options table" below 1 "vertical kink" and "outside kink" lead confgurations cannot be combined with the bulk/20 mm lead length option (wl20). 20 mm lead length is only available on capacitors ordered with straight leads (lead confguration ordering code "a"). for nonstandard lead length inquiries, please contact kemet. one world. one kemet
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 ? 864-963-6300 ? www.kemet.com c 1066_x1_760 vac_y1_500 vac ? 1/13/2017 2 packaging c-spec ordering options table packaging type lead length (mm) 2,3 packaging ordering code (c-spec) ammo pack 20.0+1.5/?1.0 (straight leads) 18.0+2.0/?0 (preformed leads 1 ) 7317 bulk bag 3.01.0 0 3.51.0 0 4.01.0 0 4.51.0 0 5.01.0 0 20.0 minimum 4 wl20 1 preformed (crimped) lead confgurations include vertical kink, outside kink and inside kink. see "lead confgurations" and "ordering information" sections of this document for further details. 2 "vertical kink", "outside kink" and "inside kink" lead confgurations cannot be combined with the bulk/20 mm lead length option (wl20). 20 mm lead length is only available on capacitors with straight leads (lead confguration ordering code "a"). for nonstandard lead length inquiries, please contact kemet. 3 for nonstandard lead length inquiries, please contact kemet. 4 lead length of 20.0 mm minimum only available for straight leads. benefts ? s afety standard recognized (iec 60384C14) ? r eliable operation up to 125c ? c lass x1/y1 ? 1 0 mm lead spacing ? l ead (pb)-free and rohs compliant ? h alogen free ? a vailable capacitance tolerances of 5%, 10% and 20% ? h igh reliability ? p reformed (crimped) or straight lead confgurations ? n on-polar device, minimizing installation concerns ? 1 00% pure matte tin-plated lead fnish allowing for excellent solderability ? e ncapsulation meets fammability standard ul 94vC0 applications typical applications include: ? l ine-to-line (class x) fltering ? l ine-to-ground (class y) fltering ? a ntenna coupling ? p rimary and secondary coupling (switching power supplies) ? l ine disturbances suppression (motors and motor controls, relays, switching power supplies, and inverters) radial leaded ceramic disc capacitors safety standard recognized, 900 series, encapsulated, as type, x1 760 vac/y1 500 vac (industrial grade)
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 ? 864-963-6300 ? www.kemet.com c 1066_x1_760 vac_y1_500 vac ? 1/13/2017 3 lead confgurations straight vertical kink outside kink d t ll s f 3.0 maximum d t ll s f 4.0 maximum 3.0 maximum d t ll s f 5.0 maximum 3.0 maximum dimensions C millimeters lead confguration lead confguration ordering code 1 s lead spacing tolerance d t e ?f lead spacing 2 body diameter 2 body thickness lead meniscus lead diameter straight a 10.0 1.0 see table 1 - "product ordering codes and ratings" 3.0 maximum 0.550.1 vertical kink (preformed) b 10.0 1.0 outside kink (preformed) c 10.0 1.0 1 lead confguration is identifed in the 13th character of the ordering code. see "lead confguration" and "ordering information" sections of this document for further details. 2 body diameter of capacitor will limit available lead spacing and packaging options. see "product ordering codes and ratings" sections of this document for further details. radial leaded ceramic disc capacitors safety standard recognized, 900 series, encapsulated, as type, x1 760 vac/y1 500 vac (industrial grade)
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 ? 864-963-6300 ? www.kemet.com c 1066_x1_760 vac_y1_500 vac ? 1/13/2017 4 approval standard and certifcation no. safety standard standard no. subclass working voltage certifcate no. vde (enec) iec 60384C14 x1 760 vac 40034867 y1 500 vac ul can/csa ul 60384C14 and e60384C14 x1 760 vac e356389 y1 500 vac these devices are vde/enec and ul recognized for antenna coupling and ac line-to-line (class x) and line-to-ground (class y) applications per iec60384C14 and ul 60384C14. environmental compliance these devices are halogen free and rohs compliant. they meet all requirements set forth by both eu and china rohs directives. general specifcations/performance characteristics dielectric/temperature characteristic y5p y5u operating temperature range: ?40c to +125c capacitance change with reference to +25c and 0 vdc applied (tcc): 10% +20%/?55% dielectric withstanding voltage 4,000 vac (605 seconds at 25oc) quality factor (q) see dissipation factor dissipation factor (tan) at +25oc 1 2.50% 2.50% insulation resistance (ir) limit at +25c 10,000 m minimum (500 vdc applied for 605 seconds at 25c) 1 capacitance and dissipation factor (df) measured under the following conditions: 1 k hz 50 hz and 1.0 0.2 vrms note: when measuring capacitance, it is important to ensure the set voltage level is held constant. the hp4284 and agilent e4980 have a feature known as automatic level control (alc). the alc feature should be switched to "on." radial leaded ceramic disc capacitors safety standard recognized, 900 series, encapsulated, as type, x1 760 vac/y1 500 vac (industrial grade)
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 ? 864-963-6300 ? www.kemet.com c 1066_x1_760 vac_y1_500 vac ? 1/13/2017 5 table 1 C product ordering codes and ratings dielectric/ temp. char. kemet part number capacitance capacitance tolerance dimensions (mm) lead spacing body diameter (maximum) body thickness (maximum) lead diameter bulk packaging ammo packaging y5p c911u101kwyd(1)a(2) 100 pf 10% 8.0 7.0 0.55 0.05 10 mm c911u151kwyd(1)a(2) 150 pf 8.0 c911u221kwyd(1)a(2) 220 pf 8.0 c911u331kwyd(1)a(2) 330 pf 8.0 c921u471kwyd(1)a(2) 470 pf 9.0 c931u561kwyd(1)a(2) 560 pf 10.0 c931u681kwyd(1)a(2) 680 pf 10.0 c951u102kwyd(1)a(2) 1,000 pf 12.0 y5u c921u102mwwd(1)a(2) 1,000 pf 20% 9.0 c931u152mwwd(1)a(2) 1,500 pf 10.0 c961u222mwwd(1)a(2) 2,200 pf 13.0 c961u332mwwd(1)a(2) 3,300 pf 13.0 c971u392mwwd(1)a(2) 3,900 pf 14.0 c981u472mwwd(1)a(2) 4,700 pf 15.0 (1) to properly complete ordering code, insert the one-digit character code to refect the required lead confguration: (see "lead confguration" section of this document, page 2, for further details.) a = s traight b = v ertical kink c = o utside kink (2) to properly complete ordering code, enter the four-digit numeric or alphanumeric "packaging c-spec ordering code". see "dimensions" section of this document, page 2, for available options. radial leaded ceramic disc capacitors safety standard recognized, 900 series, encapsulated, as type, x1 760 vac/y1 500 vac (industrial grade)
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 ? 864-963-6300 ? www.kemet.com c 1066_x1_760 vac_y1_500 vac ? 1/13/2017 6 table 2 C performance & reliability: test methods and conditions item specifcation test method operating temperature range ?40oc to +125oc dielectric strength between lead wires 2sjempyviw 8igetegmxsvwepprsxfieekiir%vwmw ettpmifixiirxipiemviwjsvwigsrw s-rwypexmsr 2sjempyviw 8ixivmrepwpiewsjxigetegmxsv weppfigsrrigxixskixiv%ixepjsmp mwxmkxpvettievsyrxifssjxi getegmxsvexemwxergisjefsyxxs jvsiegxivmrep8igetegmxsvmwxir mrwivximrxsegsrxemrivppimxixep feppwettvsmexipmrmeixiv %vwmwettpmijsvwigsrwfixiir xigetegmxsvpiemviwerixepfeppw metal foil metal balls about 3 to 4 mm insulation resistance (ir) 10,000 m minimum the insulation resistance shall be measured with 50050 vdc applied after 605 seconds of charging. capacitance within specifed tolerance capacitance is measured at 1 khz 20% and 5 vrms or less (202c) dissipation factor (df) or q df 2.5% temperature characteristics temperature characteristics capacitance change y5u within +22%/?56% a capacitance measurement is made at each step specifed: step temperature 1 +202oc 2 ?252oc 3 +202oc 4 +852oc 5 +202oc pre-treatment: capacitor is stored at 852oc for 1 hour and then placed at room condition 1 for 242 hours before measurement. strength tensile lead wire or capacitor body shall not break. with the termination in its normal position, the specimen is held by its body in such a manner that the axis of the termination is vertical; a tensile force of 10 n is applied to the termination in the direction of its axis and acting in a direction away from the body of the specimen. bending lead wire or capacitor body shall not break. with the termination in its normal position, the specimen is held by its body in such a manner that the axis of the termination is vertical; a mass force of 5 n is then suspended from the end of the termination. the body of the specimen is then inclined within a period of 2 to 3 seconds, through an angle of approximately 90 in the vertical plane and then resumed to its initial position over the same period of time; this operation constitutes one bend. one bend immediately followed by a second bend in the opposite direction. 7spivefmpmx 0iemviwsypeieyrmjsvgsexmrk sjwspivmrxiemepmvigxmsrersiv sjmxwgmvgyjivirgi 8ipiemvisjxigetegmxsvmwmttimrxsspxirwspivjsv rwigsrw8iitxsjmivwmsrmwytxs (+5/?0 mm) from the root of lead wires. solder temperature: lead free solder (sn-3ag C 0.5cu) 245c 5c. 1 room condition is defned as follows: temperature: 15 ~ 35c/humidity: 45 ~ 75%/atmospheric pressure: 86 ~ 106 kpa. radial leaded ceramic disc capacitors safety standard recognized, 900 series, encapsulated, as type, x1 760 vac/y1 500 vac (industrial grade)
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 ? 864-963-6300 ? www.kemet.com c 1066_x1_760 vac_y1_500 vac ? 1/13/2017 7 table 2 C performance & reliability: test methods and conditions cont'd item specifcation test method soldering effect (non-preheat) appearance no visual defect as shown in the fgure below, the lead wires are immersed in molten solder up to 1.5 mm (+5/?0 mm) from the end of the epoxy meniscus (root of lead wire). duration/solder temperature: 3.50.5 seconds/350c 10c or 101 seconds/260c 5c molten solder 1.5 to 2.0 mm capacitor thermal screen pre-treatment: capacitor is stored at 85c 2c for 1 hour and then placed at room condition 1 for 242 hours before initial measurements. post-treatment: capacitor is stored for 1 to 2 hours at room condition 1 . ir 1,000 m dielectric strength per item 1 capacitance within 10% soldering effect (preheat) appearance no visual defect capacitor is stored at 120c +0/?5c for 60+0/?5 seconds. then, as shown in the fgure below, the lead wires are immersed in molten solder up to 1.5 mm (+5/?0mm) from the end of the epoxy meniscus (root of lead wire). duration/solder temperature: 7.5 +0/?1 seconds/260c 5c molten solder 1.5 to 2.0 mm capacitor thermal screen pre-treatment: capacitor is stored at 85c 2c for 1 hour and then placed at room condition 1 for 242 hours before initial measurements. post-treatment: capacitor is stored for 1 to 2 hours at room condition 1 . ir 1,000 m dielectric strength per item 1 capacitance within 10% biased humidity appearance no visual defect steady state humidity: load humidity: capacitance temperature characteristics capacitance change y5u within 30% 90 to 95% humidity at 40c 2c for 500 12 hours. post treatment: capacitor is stored for 1 to 2 hours at room condition 1 . 90 to 95% humidity at 40c 2c for 500 12 hours with full rated voltage applied. post treatment: capacitor is stored for 1 to 2 hours at room condition 1 . df 5.0% maximum ir 3,000 m minimum dielectric strength no failures high temperature life appearance no visual defect impulse voltage: each individual capacitor is subjected to three 8 kv impulses prior to life testing. capacitors are placed in a circulating air oven for a period of 1,000 hours. the air in the oven is maintained at a temperature of 125c 2c throughout the test. the capacitors are subjected to ac 850 vrms. each hour the voltage is increased to 1,000 vrms for 0.1 seconds. . capacitance change within 20% ir 3,000 m m inimum dielectric strength no failures 1 room condition is defned as follows: temperature: 15 ~ 35c/humidity: 45 ~ 75%/atmospheric pressure: 86 ~ 106 kpa. radial leaded ceramic disc capacitors safety standard recognized, 900 series, encapsulated, as type, x1 760 vac/y1 500 vac (industrial grade) tr td time td (us) 46 47 tr (us) 1.2 1.5 cx (uf) pp 0.01 0.1 u pr u vp 0.9vp 0.5vp voltage
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 ? 864-963-6300 ? www.kemet.com c 1066_x1_760 vac_y1_500 vac ? 1/13/2017 8 table 2 C performance & reliability: test methods and conditions cont'd item specifcation test method flame test the capacitor fame extinguishes as follows: cycle time 1 ~ 4 30 seconds maximum 5 60 seconds maximum the capacitor is exposed to a fame for 15 seconds and then removed for 15 seconds. this test is repeated for 5 cycles. 76 capacitor flame 38 127 20o gas burner (unit:mm) active flammability the cheesecloth should not ignite. the capacitors are individually wrapped in at least one, but not more than two, complete layers of cheesecloth. they are then subjected to 20 discharges. the interval between successive discharges is 5 seconds. the vac is maintained for 2 minutes after the last discharge. s 1 tr vac s 2 c 1 l 3 l 4 c 2 c 3 c x c t vt l 1 f r oscilloscope l 2 c 1, 2 1 f 10% c 3 0.033 f 5% 10 kv l 1-4 1r%6sgsvigsoi cx test capacitor r 1002% v ac vr 5% ct 3 f 5% 10 kv v r rated voltage f fuse, rated 10a vt voltage applied to ct vx 5kv time 1 room condition is defned as follows: temperature: 15 ~ 35c/humidity: 45 ~ 75%/atmospheric pressure: 86 ~ 106 kpa. radial leaded ceramic disc capacitors safety standard recognized, 900 series, encapsulated, as type, x1 760 vac/y1 500 vac (industrial grade)
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 ? 864-963-6300 ? www.kemet.com c 1066_x1_760 vac_y1_500 vac ? 1/13/2017 9 table 2 C performance & reliability: test methods and conditions cont'd item specifcation test method passive flammability the burning time should not exceed 30 seconds. the tissue paper should not ignite. the capacitor under test is held into a fame and in a position which best promotes burning. each specimen is exposed to the fame one time. 200 5mm about 8mm 45o test specimen about 10mm thick board tissue time of exposure to fame: length of fame: gas burner length: inside diameter: outside diameter: gas butane gas purity: 30 seconds 121 mm 35 mm minimum 0.50.1 mm 0.9 mm maximum 95% minimum temperature cycle appearance no visual defect the capacitor is subjected to 5 temperature cycles. temperature cycle step temperature (c) dwell time (minutes) transition time (minutes) 1 ?40 +0/?3 30 3 2 room temperature 3 3 125 +3/?0 30 4 room temperature 3 pre-treatment: capacitor shall be stored at 852 for 1 hour then placed at room condition 1 for 242 hours. post-treatment : capacitor is stored for 1 to 2 hours at room condition 1 . capacitance temperature characteristics capacitance change y5v within 20% df/q df 7.5% ir 3,000 m m inimum dielectric strength no failures 1 room condition is defned as follows: temperature: 15 ~ 35c/humidity: 45 ~ 75%/atmospheric pressure: 86 ~ 106 kpa. radial leaded ceramic disc capacitors safety standard recognized, 900 series, encapsulated, as type, x1 760 vac/y1 500 vac (industrial grade)
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 ? 864-963-6300 ? www.kemet.com c 1066_x1_760 vac_y1_500 vac ? 1/13/2017 10 soldering and mounting information soldering: when soldering this product to a pcb/pwb, do not exceed the solder heat resistance specifcation of the capacitor. subjecting this product to excessive heating could refow the solder joint between the lead and ceramic element and/or may result in thermal shocks that can crack the ceramic element. when soldering these capacitors with a soldering iron, it should be performed under the following conditions: ? t emperature of iron-tip: 400oc maximum ? s oldering iron wattage: 50 w maximum ? s oldering time: 3.5 seconds maximum cleaning (ultrasonic cleaning): to perform ultrasonic cleaning, observe the following conditions: ? r inse bath capacity: output of 20 watts per liter or less ? r insing time: 5 minute maximum ? d o not vibrate the pcb/pwb directly ? e xcessive ultrasonic cleaning may lead to fatigue destruction of the lead wires construction detailed cross section epoxy encapsulation (0.4 mm minimum thickness, pigment = blue/ul 94 v-0) lead attach solder (sn96.5/ag3/cu0.5) electrode (ag ? glass frit) core metal barrier layer finish layer steel cu 100% sn (3-7 m) lead wire dielectric material (batio 3 ) lead attach solder (sn96.5/ag3/cu0.5) electrode (ag ? glass frit) dielectric material (batio 3 ) radial leaded ceramic disc capacitors safety standard recognized, 900 series, encapsulated, as type, x1 760 vac/y1 500 vac (industrial grade)
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 ? 864-963-6300 ? www.kemet.com c 1066_x1_760 vac_y1_500 vac ? 1/13/2017 11 marking these capacitors shall be stamped or laser marked with kemet's trademark, type designation, capacitor class, rated voltage, rated capacitance and capacitance tolerance codes. in addition, all devices are marked with the recognized approval mark and a date/lot code for traceability. marking will be supplied either on one side or both sides of the encapsulated capacitor body. all marking shall be legible to allow for clear identifcation of the component. marking appears in legible contrast. illustrated below is an example of the marking format and content. (two sided marking is limited to capacitors with body diameters 8.0 mm.) single sided ul approval mark vde & enec approval marks iec 60384-14 3rd (2005) rated capacitance (3 numeric characters) capacitance tolerance code (1 character) capacitor class and rated voltage kemet id type designation (2 characters) date/lot code (see table below) double sided capacitor class and rated voltage front back kemet id type designation (2 characters) vde & enec approval marks iec 60384-14 3rd (2005) ul approval mark date/lot code (see table below) rated capacitance (3 numeric characters) capacitance tolerance code (1 character) date/lot code explanation 6 c 6 1234 last digit of year, e.g., 6 = 2016 manufacturing location code manufacturing month: 1-9 = jan - sept a = october n = november d = december last 4 digits of lot no. radial leaded ceramic disc capacitors safety standard recognized, 900 series, encapsulated, as type, x1 760 vac/y1 500 vac (industrial grade)
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 ? 864-963-6300 ? www.kemet.com c 1066_x1_760 vac_y1_500 vac ? 1/13/2017 12 packaging quantities capacitor body diameter (mm) body diameter code 1 bulk bag (loose) ammo pack (carrier tape) component pitch on carrier tape 2 25.4 mm 7.0 0 500 pieces/bag 1,000 pieces/box 8.0 1 9.0 2 10.0 3 11.0 4 13.0 6 500 pieces/box 14.0 7 15.0 8 1 the "body diameter code" is located in the third character position of the ordering code. this code identifes the maximum diameter of the capacitor body in millimeters. for more information regarding the ordering code, see "ordering information" section of this document. 2 for details regarding component pitch on carrier tape, see "ammo pack taping format" and "ammo pack taping specifcations" sections of this document. radial leaded ceramic disc capacitors safety standard recognized, 900 series, encapsulated, as type, x1 760 vac/y1 500 vac (industrial grade)
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 ? 864-963-6300 ? www.kemet.com c 1066_x1_760 vac_y1_500 vac ? 1/13/2017 13 figure 1 - ammo pack taping format (10 mm lead spacing) l p 1 p 2 p f e d p 0 w 0 w 2 h 0 w 1 w ?d 0 ?d ?s ? table 3 C ammo pack taping specifcations lead spacing 10 mm lead style straight preformed 1 item symbol dimensions (mm) lead spacing f 10.01.0 component pitch p 25.42 sprocket hole pitch p 0 12.70.3 sprocket hole center to component center p 2 12.71.5 sprocket hole center to lead center p 1 7.71.5 body diameter d see table 1 - product ordering codes and ratings component alignment (side/side ) ?s 02.0 carrier tape width w 18.0+1.0/?0.5 sprocket hole position w 1 9.00.5 height to seating plane 2 (preformed leads 1 ) h 0 n/a 18.0+2.0/?0 height to seating plane 2 (straight leads) h 20.0+1.5/?1.0 n/a lead protrusion ? 2.0 maximum diameter of sprocket hole d 0 4.00.2 lead diameter d 0.550.1 carrier tape thickness t 1 0.60.3 total thickness (carrier tape, hold-down tape and lead) t 2 1.5 maximum component alignment (front/back ) ?h 1 2.0 maximum 2 2.0 maximum yx3yx0irkx 0 11.0 maximum hold-down tape width w 0 11.0 minimum hold-down tape position w 2 1.51.5 coating extension on leads (meniscus) e 3.0 maximum for straight lead; not to exceed the bend for preformed 1 lead confgurations. body thickness t 7.0 maximum 1 43 0 t maximum marking side ?h 1 ?h 2 t 2 t 1 radial leaded ceramic disc capacitors safety standard recognized, 900 series, encapsulated, as type, x1 760 vac/y1 500 vac (industrial grade)
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 ? 864-963-6300 ? www.kemet.com c 1066_x1_760 vac_y1_500 vac ? 1/13/2017 14 application notes: storage and operating conditions: the insulating coating of these devices does not form an air and moisture-tight seal. avoid exposure to moisture and do not use or store these devices in a corrosive atmosphere, especially where chloride gas, sulfde gas, acid, alkali, salt, or the like are present. before cleaning, bonding or molding these devices, it is important to verify that your process does not affect product quality and performance. kemet recommends testing and evaluating the performance of a cleaned, bonded or molded product prior to implementing and/or qualifying any of these processes. store the capacitors where the temperature and relative humidity do not exceed 40 degrees centigrade and 70% respectively. for optimum solderability, capacitor stock should be used promptly, preferably within 6 months of receipt. working voltage: application voltage (vp-p or vo-p) must not exceed the voltage rating of the capacitor. irregular voltages can be generated for a transient period of time when voltage is initially applied and/or removed from a circuit. it is important to choose a capacitor with a voltage rating greater than or equal to these irregular voltages. operating temperature and self-generating heat: the surface temperature of a capacitor should be kept below the upper limit of its rated operating temperature range. be sure to take into account the heat generated by the capacitor itself. when the capacitor is used in a high-frequency current, pulse current or similar current, it may self-generate heat due to dielectric loss. temperature rise due to self-generated heating should not exceed 20c (while operated at an atmosphere temperature of 25c). handling - vibration and impact: do not expose these devices or their leads to excessive shock or vibration during use. failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial dispersion when the product is used. radial leaded ceramic disc capacitors safety standard recognized, 900 series, encapsulated, as type, x1 760 vac/y1 500 vac (industrial grade)
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 ? 864-963-6300 ? www.kemet.com c 1066_x1_760 vac_y1_500 vac ? 1/13/2017 15 kemet electronic corporation sales off ces for a complete list of our global sales off ces, please visit www.kemet.com/sales. disclaimer all product specif cations, statements, information and data (collectively, the information) in this datasheet are subject to change. the customer is responsible for checking and verifying the extent to which the information contained in this publication is applicable to an order at the time the order is placed. all information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. statements of suitability for certain applications are based on kemet electronics corporations (kemet) knowledge of typical operating conditions for such applications, but are not intended to constitute C and kemet specif cally disclaims C any warranty concerning suitability for a specif c customer application or use. the information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. any technical advice inferred from this information or otherwise provided by kemet with reference to the use of kemets products is given gratis, and kemet assumes no obligation or liability for the advice given or results obtained. although kemet designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. although all productCrelated warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. kemet is a registered trademark of kemet electronics corporation. radial leaded ceramic disc capacitors safety standard recognized, 900 series, encapsulated, as type, x1 760 vac/y1 500 vac (industrial grade)

▲Up To Search▲

Price & Availability of C981U222KWDBA7317

	To Download C981U222KWDBA7317 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .